4ch / 9ch NMEA(Serial) to Ethernet Gateway. Multiplexer, Serial Switch, CAN Extender
[dropcap1]Z[/dropcap1]MG-390 and ZMG-340 are revolutionary products in which Multiplexer, Gateway and Serial switch functions can be used simultaneously.
It also support Multi protocols such NMEA 0183, IEC 61162-450, CAN, Modbus-RTU, Modbus-ASCII and any Binary data.
Of course it supports RS-232, RS-422 and RS-485 interface signals. Thus you also can use it for general Serial to/from Ethernet Gateway with Multiplexer.
This Multiplexer/Gateway has NMEA 0183 to/from IEC 61162-450 Gateway. Thus you can use it for connection non-networked equipment to IEC 61162-450 ship network.
Also ZMG-390 has Clustering function and can be extended up to 64ch serial in/out Gateway including Serial switch and Multiplexer.
ZMG-390 NMEA Multiplexer / Ethernet Gateway has 9ch Serial ports, one Ethernet and one CAN port.
It simultaneously supports Serial multiplexer, Serial switch, Serial-Ethernet gateway, Serial-CAN gateway and CAN-Ethernet gateway .
It also supports most protocols such NMEA-0183, IEC61162-450, Modbus-ASCII, Modbus-RTU and all Binary Data. And it supports all of NMEA 0183, RS-232, RS-422, RS485 and CAN signals too.
In addition, ZMG-390 has NMEA 0183 to/from IEC 61162-450 Gateway capability, which is useful for connection non-networked equipment to IEC 61162-450 ship network.
Front
Back
Power On
ZMG-390 9ch NMEA Multiplexer / Ethernet Gateway
210 x 130 x 50 mm / 0.5kg
Brochure
CE Certificate
1. Application
1. ZMG-390
1) 9ch NMEA 0183 to/from Ethernet Gateway with Multiplexer (TCP/UDP Unicast, Multicast and Broadcast)
2) 9ch Serial to/from Ethernet Gateway with Multiplexer (Modbus-ASCII, Modbus-RTU and General Binary Data, RS232 RS422 RS485 signal)
3) 9ch x 9ch Serial Switch (Serial to Serial routing, Conversion of Baud rate, Data length, Parity and Stop bit)
4) Very high perfromance Tx and Rx (Up to 230,400bps for all Tx/Rx)
5) Combine and switch up to 32ch serials (Cluster Mode)
6) Record serial data to micro SD card from selected channel. (FAT 16/32, exFAT)
2. ZMG-390pro (Professional)
1) Including all functions of ZMG-390
2) 9ch NMEA 0183 to/from IEC 61162-450 Gateway with Multiplexer (LWE: Light Weight Ethernet)
3) CAN (NMEA 2000) to/from Ethernet Gateway
4) 9ch Serial to/from CAN Gateway
2. Serial Port
| 9 Serial Tx/Rx Ports | – 8 Rx Galvanic Isolating Ports (NMEA 0183, RS422, RS232, RRL,C/L – 2 NMEA 0183HS (IEC61162-2) ports |
| Protocol | – NMEA-0183/HS, Modbus-ASCII, Modbus-RTU, Binary Data |
| Protection | – A Protection against Over voltage input (up to 36V) |
| Baud Rate | – 1,200bps ~ 230,400bps by each port (9 Steps) |
3. CAN (Pro only)
| Protocol | – CAN 2.0A/B (NMEA-2000/IEC 61162-3, SAE J1939, other CAN-based Systems) – Raw data (Does not decode PGN’s and transport the CAN frames) – Galvanic isolation |
| Speed | – 100kbps, 125kbps, 250kbps, 500kbps, 1Mbps. |
4. Ethernet
| Protocol | – TCP/IP TCP/UDP Unicast and Multicast. – IEC61162-450 Light Weight Ethernet Protocol. (Pro only) – TCP/IP TCP and HTTP for System configuration. |
| Speed | – 100Kbps, 125Kbps, 250Kbps, 500Kbps, 1Mbps |
5. Configuration
| Serial Port | – Baud rate, Data Length, Parity bit and Stop bit by each port. |
| Network | – Source and destination IP address and Port, Single/Multi Mode |
| Routing | – Between Serial, CAN and Ethernet by each Channel |
6. General Specifications
| 1) Display and Monitor | |
| Monitor | – Success packet and Error packet counter through dedicated TCP/UDP port |
| LED | – Operation status (Power, Input data) |
| 2) Input Power | |
| Voltage | – DC 12/24V (10~32V), Approximately 500mA at 12V |
| Fuse | – Electric Fuse, No Replacement Required |
| 3) Physical Specifications | |
| Dimension | – 210 x 130 x 50mm (Including Terminal blocks) |
| Weight | – 1.0kg |
| Terminal | – Removable Screw Terminal Blocks |
| – This specifications may be changed without any notifications. – If you advise good idea or improvement or any other specifications for our products, then we will strongly consider it. |
|
[hr top]
ZMG-340 NMEA Multiplexer / Ethernet Gateway has 4ch Serial ports, one Ethernet and one CAN port.
It simultaneously supports NMEA(Serial) multiplexer, Serial switch, Serial-Ethernet gateway, Serial-CAN gateway and CAN-Ethernet gateway.
It supports most serial protocols such NMEA-0183, Modbus-ASCII, Modbus-RTU and Binary Data. It also supports all of NMEA-0183, RS-232, RS-422, RS-485 and CAN signals.
In addition, this ZMG-340 has NMEA IEC 61162-450 Gateway capability.
ZMG-340 4ch NMEA Multiplexer / Ethernet Gateway
ZMG-340
90 x 138 x 42 mm / 0.5kg
Brochure
CE Certificate
1. Application
1. ZMG-340
1) NMEA 0183 Multiplexer / Ethernet Gateway (UDP Unicast, Multicast and Broadcast)
2) Serial Multiplexer / Ethernet Gateway w(Modbus-ASCII, Modbus-RTU and Binary Data, RS232 RS422 RS485 signal)
3) Serial Switch (Serial to Serial routing, Conversion of Baud rate, Data length, Parity and Stop bit)
4) Very high speed Tx and Rx (Up to 230,400bps for all Tx/Rx ports)
2. ZMG-340pro (Professional)
1) NMEA 0183 to/from IEC 61162-450 Gateway with Multiplexer (LWE: Light Weight Ethernet)
2) CAN to/from Ethernet Gateway.
3) Serial to/from CAN Gateway
4) CAN communication distance extension(N2K devices are available)
2. Serial Ports
| Serial Ports | – Each Serial port is selected as Tx or Rx by internal jumper. – Max 4 Rx channels, Galvanic isolation (NMEA 0183, RS-422, RS-232, TTL and Current-Loop signals acceptable) – Max 4 Tx channels, RS-422 Output (NMEA 0183) – 2 RS-485 bidirectional channels |
| Protocol | – NMEA-0183/HS (IEC 61162-1/2), Modbus-ASCII, Modbus-RTU, Binary Data |
| Protection | – A Protection against Over voltage input (up to 36V) |
| Baud Rate | – 1,200bps ~ 230,400bps by each port (9 Steps) |
3. CAN (Pro only)
| Protocol | – CAN 2.0B (NMEA-2000/IEC 61162-3, SAE J1939, other CAN-based Systems) – Raw data (Does not decode PGN’s and transport the CAN frames) – Galvanic isolation |
| Speed | – 100kbps, 125kbps, 250kbps, 500kbps, 1Mbps. |
4. Ethernet
| Protocol | – TCP/IP UDP Unicast and Multicast. – IEC 61162-450 Light Weight Ethernet Protocol. (Pro only) – TCP/IP TCP and HTTP for System configuration. |
5. Configuration
| Serial Port | – Baud rate, Data Length, Parity bit and Stop bit by each channel. |
| Network | – Source and Destination IP address and UDP Port, Single/Multi UDP Mode |
| Routing | – Between Serial, CAN and Ethernet (UDP) by each Channel |
6. General Specifications
| 1) Display and Monitor | |
| Monitor | – Success packet and Error packet counter through dedicated UDP port |
| LED | – Operation status (Power, Input data) |
| 2) Input Power | |
| Voltage | – DC 12/24V (10~32V), Approximately 300mA at 12V |
| Fuse | – Electric Fuse, No Replacement Required |
| 3) Physical Specifications | |
| Dimension | – 90 x 138 x 42mm (Including Terminal blocks) |
| Weight | 0.5kg |
| – This specifications may be changed without any notifications. – If you advise good idea or improvement or any other specifications for our products, then we will strongly consider it. |
|
7. Products that can be replaced as ZMG-340
| ADVANTECH | EKI-1511, EKI-1522, EKI-1524 |
| MOXA | Nport 5100, NPort 5200, Nport 5400 |
[hr top]
ZMG-340SC Sentence Converter is a converter from NMEA0183 standard sentence to non standard sentence formats such Tokimec, Yokogawa, Anrits and etc.
The hardware is exactly same as ZMG-340.
It is very useful for interfacing between different maker’s products with using private sentences.
It is also very useful for installation Autopilot system which needs private sentences. It can be made from standard NMEA0183 sentences such GPS gyro, Gyrocompass, Speed log, ROT device and etc.
ZMG-340SC Sentence Converter
ZMG-340SC
90 x 138 x 42 mm / 0.5kg
- NMEA to Tokimec : Heading, Speed, ROT(Rate of Turn)
<STX> G123.4,L56.7,R 008.9 <ETX> - NMEA to Yokogawa : Heading, ROT
$HEHRC05320,-080*59<CR><LF> - NMEA to Anschutz (CourseBus): Heading, ROT
<STX> B1 …B16 <ETX> - If there are other sentences you want to convert, we can customize and add them.
[hr top]
ZMG-340NTP Server receives time information from GPS receiver and synchronization of internal clock and transmits the received time information to external equipment using NTP(Network Time Protocol).
It is used for responding when receiving for synchronization clock request from the client. User also can passively broadcast or multicast in the place where receives to time update by using ZMG-340NTP.
ZMG-340NTP Network Time Protocol Server
ZMG-340NTP
90 x 138 x 42 mm / 0.5kg
Brochure
1. Features
2. Specifications
| 1) Serial | |
| 4 Serial Ports | – Each Serial port is selected as Tx or Rx by internal jumper. – Max 4 Rx channels, galvanic isolated. (NMEA-0183, RS-422, RS-232, TTL and Current-Loop signals acceptable) – Max 4 Tx channels, RS-422 Output (NMEA-0183) – Max 2 RS-485 bidirectional channels |
| Protection | – A Protection against Over voltage input (up to 32V) |
| Baud Rate | – 1,200bps ~ 230,400bps by each port (9 Steps) |
| Sentence | – Support ‘ZDA’ Sentence (‘RMC’ will be added) – Support to select input channel |
| 2) Ethernet | |
| Ethernet | – 10 / 100 Base T Ethernet, Automatic Tx/Rx Sense – Support NTP Broadcast, Multicast, Unicast (Query) Mode – Support NTP Version 3/4 – Web Based Configuration |
| NTP Protocol | – Unicast Mode : UDP on port number 123 – Broadcast/Multicast Mode : User can set IP address, Port number, Period. |
| 3) Physical Specifications | |
| Dimension | – 90 x 138 x 42mm |
| Weight | – 0.5kg (Including Terminal blocks) |
| – This specifications may be changed without any notifications. – If you advise good idea or improvement or any other specifications for our products, then we will strongly consider it. |
|
[hr top]